How To Set Page Limit In Autocad

Limits Command

The Limits command in AutoCAD is used to set an invisible rectangular purlieus in the cartoon area or viewport. It limits the filigree brandish and the indicate locations.

We are required to specify the coordinates of the opposite corners of the rectangular window. The opposite corners are named equally Upper right and Lower left corners.

The contrary corners are shown in the beneath image:

Why nosotros need limits?

Some dimensions in a cartoon are represented in hundreds and thousands of meters. For example, bridge designing in AutoCAD, Architecture designing, etc.

The representation of such large dimensions is difficult in a regular cartoon expanse. For such purposes, limits play a vital role in setting the purlieus of the drawing area. We tin specify the limits according to our requirements.

Limits Checking

The two options under limits checking are:

ON
It turns ON the limit checking. It tests just the points we enter, and then we cannot specify the points exterior the filigree limits. But portions of circles and other objects can extend exterior the grid limits.
OFF
It turns OFF the limit checking. The current value of limits is maintained for the side by side fourth dimension when we turn ON the limits.

Steps to ready the limits

The steps to set the limits are listed below:

Open up the AutoCAD software.
Type LIMITS on the command line or control prompt.
Printing Enter or spacebar.
Write the coordinates of the lower-left corner. For example, (0,0). The coordinates for the lower-left are usually the coordinates of origin for better understanding. We can besides modify the coordinates according to the requirements.
Printing Enter.
Write the coordinates of the upper-right corner. For example, (200, 200).
Printing Enter.
Write Z. Hither Z signifies Zoom.
Press Enter.
Write Eastward. Hither, E signifies Extend.
Press Enter.

The Z and E are mandatory to activate the limits. It is likewise called a regenerating style of limits.

Now, we can rapidly create drawings within the dimensions mentioned above.

Note: The dimensions of a figure should exist within the specified limits. If it is greater, we can re-specify the limits according to the requirements.

Let'south understand limits with few examples.

Example 1:

Draw a rectangle of dimension 100 10 200.

Here, the length of the rectangle is 100, and the width is 200.

The steps are listed below:

Blazon LIMITS on the control line or command prompt.
Printing Enter.
Write the coordinates of the lower-left corner (0, 0).
Press Enter.
Write the coordinates of the upper-right corner (300, 400). You lot can also increase the limits co-ordinate to your choice.
Press Enter.
Write Z. Hither Z signifies Zoom.
Press Enter.
Write East. Here, Eastward signifies Extend.
Printing Enter.
Type Rec or Rectangle on the control line.
Press Enter.
Specify the first corner indicate on the viewport.
Specify the length and breadth of the rectangle in the form of @length, width. For example, @100,200
Printing Enter.

Using above steps, the rectangle will exist created.

Example 2:

Draw ii adjacent squares of side 200. The gap between the squares should exist l.

The length of the effigy will be 200 (side of square1) + 50 (gap) +200 (side of square2) = 450. And then, we will specify the limits greater than the dimensions of the figure.

The steps are listed below:

Blazon LIMITS on the control line or command prompt.
Press Enter.
Write the coordinates of the lower-left corner (0, 0). You can set the coordinates co-ordinate to the choice.
Printing Enter.
Write the coordinates of the upper-right corner (700, 600). You tin can likewise increase or adjust the limits according to your choice.
Printing Enter.
Write Z. Here Z signifies Zoom.
Press Enter.
Write East. Here, Eastward signifies Extend.
Press Enter.
Type Rec or Rectangle on the command line.
Press Enter.
Specify the kickoff corner bespeak on the viewport.
Specify the length and breadth of the rectangle in the form of @length, width. For case, @200,200
Printing Enter.
Now, nosotros will depict another square adjacent to the first square. For the gap of l, we will move the second foursquare and will specify the displacement value 50. You tin can utilize other methods as well.
Once more type Rec or Rectangle on the command line.
Press Enter.
Specify the corner indicate of the first square.
Specify the length and breadth-@200,200
Press Enter.
Type M or Move on the command line and press Enter.
Select the 2d square.
Press Enter.
Specify the base point and requite the direction through the cursor.
Write the displacement = l.
Press Enter.

The effigy will exist created, equally shown in the beneath image: